Interested in linking to "Detecting Bunker C Oil Mass Flow"?
You may use the Headline, Deck, Byline and URL of this article on your Web site. To link to this article, select and copy the HTML code below and paste it on your own Web site.
Question: I have problem of selecting a suitable flowmeter for a heavy liquid, Bunker “C” Oil. Bunker “C” fuel oil is a sticky, black liquid similar in appearance and smell to asphalt sealing compounds. At 10 °C it has a consistency of liquid honey or corn syrup. At 0 °C it barely flows. It has the following specifications:
What is the suitable flowmeter for this application (electromagnetic, ultrasonic, mechanical, etc.)?
Control & Instrumentation Engineer
Answer: If volumetric measurement is good enough, use an oval gear or viscous helix PD meter with steam or electric tracing, in SS or Hastelloy C construction. If mass flow measurement is needed, use a 4-in., self-draining, heated, Hastelloy C Coriolis flowmeter. The main advantages of these meters include their high accuracy (0.1% of the actual flow rate) and excellent rangeability (up to 100:1). Their main disadvantages are high cost and that they can not be used on liquid services with significant gas content. Also be careful not to install them at high points or in a downward flows, because they must alwats be flooded. For costs, suppliers, capacities and other details see Chapters 2.11 and 2.19 in the 4th edition of the first volume of The Instrument Engineer’s Handbook.
Answer: The four types of flowmeter used to measure bunker oil are differential pressure, transit time ultrasonic, coanda effect, coriolis effect. It is relatively straightforward to get mass flow from any of these.
Differential pressure requires a flow element, either an orifice plate, or a venturi or a v-cone. The abrasive and corrosive nature of bunker oil makes this measurement (with temperature sensor for density compensation and thus mass flow) a maintenance issue. This type of meter is generally the least costly.
Coriolis meters are becoming less vibration-, abrasion- and corrosion-sensitive all the time. Sizes up to 12-in. diameter are becoming more common, with at least four vendors now supplying larger sized meters than 4-in. diameter. This is still the most expensive, but probably the most accurate option.
Coanda meters are quite accurate and can be compensated for density. There is, however, only one vendor at this time, a small company in Phoenix, Ariz,, Fluidic Flowmeters LLC.
Transit time ultrasonic flowmeters of the multipath variety are becoming more common for this application because they have fewer issues with maintenance arising from abrasion and corrosion resistance.
Editor in Chief
Answer: A screw-type positive displacement flowmeter is a good choice under these conditions; one which I have used for similar duty is found at www.maxmachinery.com/specsfm/243.pdf.
Your application is, however close to the maximum design condition for their 3-in. meter, and they don’t make a larger one. KRAL AG (www.kral.at/flowmeters_omg_techdata+M5d637b1e38d.html) has a larger one of similar design.
Ian H. Gibson,
Principal Technical Specialist
Answer: A Brooks oval gear meter BM type can tackle high viscosities. Otherwise, if the line can be kept warm, a Coriliolis meter with a heated sleeve would be best.
Stephan Gaertner, P.E.
Answer: I would suggest using a Coriolis because the high viscosity eliminates vortex and the non-conductive nature eliminates the magnetic flowmeter.
Due to the sulfur content, it is advisable to consider stainless steel, Hastelloy C or titanium materials of construction.
Attention must be paid to the pressure loss. We checked the application with a specific Endress+Hauser model, and the pressure drop was slightly below 1 bar with a 3-in. coriolis, and 0.3 bar with a 4-in. coriolis. The size should be decided as a function of pumping costs vs. first cost.
Finally, considering that the fluid has high viscosity at ambient temperature, the installation should be self draining to empty the meter at shut off, before the fluid becomes cold.
Endress+Hauser Controle e Automação
São Paulo, Brazil
Answer: I think that a PD meter could be OK, well-heat traced.
Dr. Alberto Rohr
Question: I am an instrument and control engineer, active in the field of oil & gas projects. I need the answers/clarification to the following question: Can we use the unit control panel of a turbo compressor as the ESD of the whole station? Does this meet any rules and regulations?
A heated oval gear meter can tackle high viscosities.
I would proceed as follows, asking these questions:Answer:
If the calculated SIL fits with the required SIL of the ESD functions, it is possible to use the unit control panel as the logic solver.
Also note the following:
A) It is necessary that the control system is fully independent from the ESD system, in order to have a different line of defense in case the ESD fails completely, for instance due to power feed or other common cause of failure.
B)According to the severity of required SIL, the components of the safety loops need to be selected properly and certain precautions taken, for instance, using self checking transmitters (double sensors with comparator), partial stroke test for the valves, etc.
Dr. Alberto Rohr
Answer: NO. The control system may fail in such a way as to cause a demand on the safety system. A safety instrumented function within the control system may likely be failed due to the same cause. This represents very high risk.
Dr. William M. Goble C.F.S.E
Sellersville, PA 18960