...to Tango

Model-Predictive Control and Advanced Process Control Tools Are Helping Users Gain Efficiencies and Savings in Their Process Applications. Here’s How You Can Boogie to the Optimization Beat, Too

1 of 2 < 1 | 2 View on one page

Data Collection and Optimization, Part 2
See Part 1, It Takes ...

By Jim Montague, Executive Editor

Another dance? Mais oui. Faster this time? I guess. So you might think that coaxing a few precious nuggets of useful data out of your application would be the hardest part of data collection, and that all you need to do to optimize your process is plug them into it. Sorry, Mr. Astaire.

In fact, plowing intelligence back into a process to make improvements can be even harder than finding it in the first place. Besides choosing and implementing the right hardware and software, there are many other jobs that all need to be done right for optimization efforts to really pay off. Probably the two most important of these are developing models and model-predictive controls that genuinely reflect the application in which they’re going to be used, and then training operators, technicians, engineers and managers to make those controls part of their daily work routines.

Instilling Stability

Prohibition may be over, but making alcohol is still risky. For example, the East Kansas Agri-Energy ethanol plant in Garnett uses a six-step, dry-mill process to ferment corn into sugar and then distill it into alcohol, and annually produces 35 million gallons of 200-proof ethanol, 68,000 tons of dried distiller’s grains with solubles (DDGS) and 110,000 tons of wet distiller’s grains with solubles (WDGS). Doug Sommer, EKAE’s plant manager, reports that controlling the cooking process is difficult because of disturbances from in-plant water recycling. Added challenges come from trying to maintain consistent DDG and syrup-solids moisture levels.

More recently, increasing ethanol demand pushed EKAE to move from a half-week to a full-time production schedule. To increase its dryer capacity by 4% to 6%, reduce energy use by 2.5% to 3% and increase ethanol production via more stable plant control, EKAE enlisted Rockwell Automation subsidiary Pavilion Technologies to help implement an advanced process control (APC) system for the plant’s milling, cooking and stillage-dehydration sections. This APC system is based on a nonlinear, model-predictive control (NMPC) method, a control algorithm based on a dynamic-process model of EKAE’s process, so it can predict and optimize future responses. EKAE’s models combined fundamental and empirical models derived from plant measurements.    

As a result, EKAE’s APC system includes two controllers—one configured for the milling and cooking section and a second for the stillage-dehydration section. The objectives for the milling/cooking section were to balance load and energy between mills for efficient milling; increase feed to beer column to increase ethanol production; manage fermentation inventory with the water balance; control liquefaction and slurry solids percentages to reduce disturbance to the fermenters; and control backset percentage to ensure a constant mineral feed to the fermentation process to maintain consistent water quality in the fermentation feed. Goals for the stillage-dehydration section, including centrifuges, evaporators and dryers, were to balance load distribution between centrifuges; decrease energy use in ethanol production; control dryer moisture for consistent DDG product quality; reduce average thermal oxidizer (TO) hotbox temperature while maintaining temperature within environmental limits; and stabilizing steam pressure within the TO’s operating limits.

To accomplish these objectives, Sommer says liquefaction, evaporator solids and dryer moisture were controlled to meet an operator-determined target using values predicted in real time from virtual online analyzers (VOA) developed by Pavilion. Likewise, backset flow was manipulated by the water balance controller, and the trajectories were sent to the slurry/stillage controller. Slurry solids were controlled by manipulating corn and water amounts to the slurry tank. The operator decided on a target value for liquefaction solids. The application calculated the slurry solids target value required to achieve the desired consistency of the liquefaction solids. The application included virtual online analyzers for slurry, liquefaction and syrup solids, as well as dryer product moisture. These analyzers in turn provided real- time calculations to the controller.

Before APC was installed at EKAE, its beer feed flow rate average was roughly 511 gpm. After APC was added, beer feed flow rate increased 3.6% to an average of 529.3 gpm. In addition, 190-proof production was 91.4 gpm on average before APC, and it increased to 104.5 gpm after APC. Most important, the average 200-proof flow to storage increases from 74.6 gpm to 84.2 gpm, which represents a 12.8% increase in ethanol production (Figure 1). Also, energy use of steam in lbs/gal of ethanol improved approximately 9.7%.

advanced process control
Figure 1. East Kansas Agri-Energy (EKAE) used advanced process control (APC) to increase its production of 200-proof ethanol by 12.8% from 74.6 gpm (pink line) to 84.2 gpm (blue line).

Besides its quantitative benefits, NMPC also gave EKAE automation with the following advantages: Models don’t require major adjustment unless major modifications to the process are carried out; process is kept stable during fluctuating conditions, such as changes in the weather or upsets in the distillation section; and better control of the fermentation/beerwell inventories makes it easier to manage the milling rate with the beer feed target rates.  This stability increased the plant’s ability to push production rates to capacity.

1 of 2 < 1 | 2 View on one page
Show Comments
Hide Comments

Join the discussion

We welcome your thoughtful comments.
All comments will display your user name.

Want to participate in the discussion?

Register for free

Log in for complete access.


No one has commented on this page yet.

RSS feed for comments on this page | RSS feed for all comments