Radar Technology for Level Measurement

Precise Knowledge of the Grain Level in UCML's Storage Silos Is Essential to Production. Radar Measurement Is the Key

2 of 2 1 | 2 > View on one page

All of this took place at UCML with malted barley grain arriving by rail car or truck every few days. Grain delivery was always a control headache, as the silo's capacity is much less than the more than 70 metric tons (MT) on a rail car. With the variable delivery schedules and the expense of rail car unloading demurrage time, it is crucial to have constantly accurate inventory level measurement. Precise inventory monitoring ensures that unloading from rail cars or trucks takes place within the allotted days, and without exceeding the silos' capacity, since cleanup of spilled grain on surrounding streets is not easy. We also wanted the ability to coordinate the brewing usage of the grain discharged from the silos without shutting down production, as this would save both time and money.

UCML investigated several options for reporting silo grain levels. Load cells, a very accurate method, were too expensive to retrofit onto our existing silos. Repairing our weight and cable system's electronics was also quite costly, considering its mechanical problems. An ideal system would have mechanically and electronically reliable construction, and would be accurate over the full length of the silo—especially the bottom cone discharge section. Such a solution would also have a remote readout capability at some distance from the silo and capability for a high- and low-level alarm shut-off option. Finally, it must be able to handle the grain silo's intense dust level during the filling cycle.


United Canadian Malt was already familiar with Siemens Industry's level measurement transmitters in its manufacturing process. UCML had previously installed a Sitrans LG200 guided wave radar transmitter on a wort tank. Wort is a challenging substance to measure because of high temperatures and excessive steam and foam that are generated during the wort transfer process. The tank also requires a weekly chemical sanitation bath and a high-pressure water washdown, and there is little headroom, complicating the installation of any instrumentation.

The installed Sitrans LG200 operates with a flexible, single cable probe with a sanitary tri-clamp fitting. The transmitter is connected to a remote display at the operator's station to enable  convenient remote monitoring. The LG200 performs consistently and accurately, despite at times working through a meter of foam and its accompanying sticky residue. This unit has done so for several years, which imparts a great deal of confidence in the reliability of Siemens' instruments, both from our production and maintenance operators' standpoints.
UCML's first silo level control monitoring device was a Sitrans LR460 installed on the first of our two outdoor silos. It is connected to a remote display inside the building. Sitrans LR460 is a non-contacting, 25-GHz frequency-modulated continuous wave (FMCW) radar level transmitter, and it uses a four-wire connection (two for 115 VAC power supply and two for the mA output). After some fine-tuning of the signal, Sitrans LR460 provided reliable operation.

The Sitrans LR460 uses a 4-in. horn antenna with an 8° beam angle. Due to the center location of the Sitrans LR460, the transmitter was detecting the seams of the silo, which were tuned out via the process intelligence feature called "Auto-False-Echo-Suppression." This process required the silo to be near empty. Once configured, Sitrans LR460 provided acceptable readings, except for the lower cone area.  

With the success of the both the Sitrans LG200 and the Sitrans LR460 in mind, United Canadian Malt selected the new Sitrans LR560 for a solution for level measurement of the second silo. The stainless-steel housing was readily adaptable to UCML's preferred way of installation on our silo inspection hatch, and its compact size made it easy to carry the transmitter to the top of the silo for the installation. From our electrician's point of view, the unit's two-wire configuration was also instrumental in saving installation work and wiring costs.

Sitrans LR560 uses a high frequency of 78 GHz and a unique lens antenna to provide a narrow 4° beam. The local display interface has an easy-to-use, graphical Quick Start Wizard that allowed operators to set up the Sitrans LR560 in a couple of minutes using the display pushbuttons. The extreme narrow beam of Sitrans LR560 provides plug-and-play performance, and no additional fine-tuning was required. The seams of the inside of the silo did not interfere with the level readings, and reliable readings are provided all the way to the bottom of the cone area.

Sitrans LR560 is available with HART, Profibus PA or Foundation fieldbus protocols. Programming can be performed remotely with Simatic PDM (process device manager), AMS or PACTware with Siemens' DTM. The local display interface features a backlit display, and can be rotated in four positions. An integrated purge connection is readily available for self-cleaning of the antenna lens if the solids material is exceptionally sticky.The 78-GHz frequency creates a very short wavelength that provides exceptional reflection from sloped surfaces and aiming is rarely necessary. An optional aiming flange is available to aim the antenna away from obstructions or towards the center of the discharge cone for reliable readings in the cone area.


Since the Sitrans LR560 was installed, UCML's operators have noticed very stable readings from the transmitter, from completely empty to full. During filling, our operators simply keep an eye on the remote display, monitor the filling cycle and then shut the transfer system off if the level approaches the top of the silo. There has been zero maintenance on the Sitrans LR560 since its installation, and no maintenance is expected.

UCML's silo cleaning schedules have also benefitted from the Sitrans LR560's compact design. Its low profile and lack of extended horn have meant a significantly easier—and safer—cleaning process for the two workers who are on top of the silo performing the required operation. The yearly maintenance cost associated with the previous mechanical level system has been eliminated. In fact, the cost of the new equipment was paid back well within the first year of its operation. 

Overall, as the general manager at United Canadian Malt, I am very happy with all of the instruments we're using from Siemens Industry. We have acceptable performance from the Sitrans LR460, and we were very surprised with the small size of the Sitrans LR560 and how much easier it was to install, set up and operate. Our operators know what is going on throughout our process, and we no longer have any overfilled silos or inaccurate readings from old technology. 

Monte Smith is general manager at United Canadian Malt Ltd. 

2 of 2 1 | 2 > View on one page

Join the discussion

We welcome your thoughtful comments. Please comply with our Community rules.
All comments will display your user name.

Want to participate in the discussion?

Register for free

Log in for complete access.


No one has commented on this page yet.

RSS feed for comments on this page | RSS feed for all comments