Piercing thick flow problems

Oct. 20, 2016
From mud slurries to butter, tough measurement problems often call for clever solutions.

Difficult flow measurement problems require innovative solutions, ranging from using existing flowmeters in a unique way to developing entirely new technologies because current instruments can’t handle the application. In this article, we’ll look at several creative solutions to flow measurement issues.

Build a better Coriolis meter

Keith Simpson is the I&E controls manager for Continental Carbon, which makes carbon black in Houston. Simpson recently helped develop a new process for producing carbon black, but he and his colleagues couldn’t measure mass flow with any existing products. They had to measure the mass flow rate of a feedstock coming out of a preheater at 500-600 °F.

“At the time, no manufacturer made a Coriolis meter that would run at temperatures that high,” says Simpson. “We tested several, burned them up in our pilot plant, and proved they wouldn’t work.”

Simpson explained the problem to Micro Motion, which developed the DT Series Coriolis meter to address his issue (Figure 1). “The meter ran very successfully, gave us the accuracy we required, and operated at the full temperature range that was necessary, and we were able to begin manufacturing this very specialized product,” says Simpson. “Without Micro Motion, I don’t think we’d have been as successful. We would have had to do things differently, and we wouldn’t have been as efficient.” [A video about this application is available here.]

Extreme environments

[sidebar id =1]“The difficulty of applying flowmeters to most processes tends to increase when the application entails relatively extreme operating conditions,” explains David Spitzer, partner and co-founder at consultant Spitzer & Boyes. For example, a metal flowmeter is usually better than a plastic flowmeter if the fluid is hot. The flow of abrasive fluids is usually better measured using an obstruction-less flowmeter. Flowmeters that can be easily cleaned are usually preferred when fluid can plug the sensing element.

“Applications that exhibit one of these relatively extreme operating conditions generally tend to eliminate consideration of several flowmeter technologies. Further, it can be downright difficult to find a viable flowmeter that can measure accurately when multiple extreme operating conditions are present at the same time.”

In one application, Spitzer had almost the same problem as Simpson—trying to measure hot fluids, this time in an incinerator. The incinerator temperature was controlled to maintain approximately 1,000 °C by measuring and controlling flows of various simultaneously fired fuels, fume streams from various process units and combustion air. 

“The operators wanted a meter to measure the flow of distillation residues to the incinerator, so they’d know the pipe was properly cleaned and not plugged,” says Spitzer. “So the flowmeter had to measure liquids and gases that could be hot or warm, plus be rugged enough for the operator to occasionally use a hammer and chisel to remove solids from its body.”

In this case, the solution was a wedge flowmeter. “The differential pressure that a wedge flowmeter produces can measure liquids and steam,” says Spitzer. “The flowmeter was fitted with chemical tee and remote diaphragm seal connections that eliminated impulse tubing, and located the diaphragm flush with the flow. The operators could unbolt the diaphragm seals and chisel out residue from the rugged all-metal, wedge-flow element. A local switch was installed to signal the type of operation, residue or steam, so the control system would know when to include the heat value of the residue in the incinerator’s heat calculations.”

Clobbered by mud

Unlike the challenges of heat, Jason Norman, a consultant and drilling fluids engineer with Zaxxon Instruments, had a clogging problem with drilling mud, and he solved it with plumbing and maintenance.

“We were working with a large independent operator in the Texas Panhandle, using two 4-in. Coriolis meters on the mud pumps plains. “We incorporated green cement into the active mud system, which caused the drilling fluid to gel up due to excessive water incorporated into the system. We refer to it as ‘clobbered up mud.’ We didn’t have a meter bypass built into the plumbing, which resulted in excessive downtime while we waited for the crew to break apart the meters to clean the inside of the tubes.

[sidebar id =4]

“The lessons we learned were to always build in a meter bypass, so operations can continue pumping during meter maintenance intervals, and develop preventive maintenance routines for operations that can cause cold mud to gel inside the meters.”

Denver Smart, vice president of oil and gas marketing at Emerson Process Management, reports that the growing trend to cut drilling costs despite increased well complexity has prompted oilfield service companies to implement more advanced measurement solutions for drilling fluids (mud) management. “Using flowmeter technology to continuously measure drilling fluid returns is a challenging application,” says Smart. “The various oil-water-base slurries, changing physical properties, potential for entrained gas and the presence of rock cuttings significantly impact the accuracy and reliability of flow and density instruments.”

Coriolis flowmeters are widely used in oilfields. Before Coriolis, methods for measuring flow typically involved mechanical paddle meters and/or pit-level measurements. Both have issues with accurate and/or timely flow measurement of the drilling fluids return stream.

“For Coriolis technology, the measurement performance at flow trndown ratios up to 100:1 lets us use large-capacity meters to prevent erosion and cuttings plugging the flow line, while reducing backpressure effects in gravity-feed applications,” Smart explains. “Best practices have been established to ensure full stream flow through the meters under gravity feed, resulting in real-time sustained measurement performance and reliability. This provides a level of drilling operational diagnostics to avoid well-control events, reduced drilling efficiency and higher operating costs.”


Two frequencies better than one

Older, 60-Hz magmeters have a difficult time measuring the white and black liquors in pulp and paper processes. These are particularly difficult in slurry applications due to the presence of wood chips and other pulp material.

“High-frequency, AC magmeters do a good job of reducing slurry noise, but they have poor accuracy and problems with zero stability. DC magmeters can’t be effectively used in this type of application due to the presence of low-frequency slurry noise,” explains Tom Figlik, field instrument consultant at Yokogawa Corp. of America. “In this and similar applications, dual-frequency magmeters combine the best of high- and low-frequency meters. In addition, dual-frequency magmeters use both high 75-Hz frequency and low 6.25-Hz frequency excitation. Dual-frequency excitation superimposes high frequencies on low frequence.”

More pressure for paper

Likewise, a German pulp and paper manufacturer wanted to increase steam pressure at the inlet of the dryer section of a paper machine to increase production. The company measured steam flow to determine the proper amount of specific energy to apply for optimal paper production. The existing orifice-plate, differential pressure (DP) flowmeter wasn’t suited to this high-pressure service because it caused a substantial reduction in pressure.


As a result, the papermaker replaced its old meter with a Rosemount 3095MFA Annubar flowmeter (Figure 2). Its calculations showed low permanent pressure loss versus an orifice-plate meter, and minimal modifications were needed to the existing piping. The new flowmeter provided a pressure- and temperature-compensated measurement in one package.

After replacing its old flowmeter with the Annubar, the paper machine achieved record high paper production due to increased pressure in its steam heads. Consequently, the paper company also achieved higher production rates and efficiencies.

However, one replacement project doesn’t mean orifice-plate flowmeters are no longer useful, even though they require relatively long straight-pipe runs upstream and downstream of the meter, which is an issue in many retrofit applications. “In the nuclear industry, additional regulations following the Fukishima disaster are calling for more flow measurements in existing pipes for parameters like non-safety-related cooling water,” says Wally Baker, pressure content marketing manager at Rosemount (www.rosemount.com). “When flow measurements are required on existing infrastructures, it can be challenging to meet best practices for installation, including requirements for straight-run piping for orifice-plate measurements.

[sidebar id =2]“Fortunately, conditioning orifice plate (COP) technology enables users to perform these measurements because it doesn’t require the traditional four pipe diameters of upstream pipe. A COP only requires two pipe diameters upstream to make an accurate flow measurement. This enables users to make these newly required flow measurements with little or no piping modifications,” concludes Baker.

Measuring butter flow

Nathan Hedrick, flow product marketing manager at Endress+Hauser, reports having a customer that needed to measure flow of butter as a part of a large batching process for making baked goods. The butter had to stay below 40 °F, but at that temperature it no longer flowed as a liquid, was highly viscous, and trapped a lot of air. “The customer was using a Coriolis mass flowmeter to measure flow,” notes Hedrick. “Initially, the readings were unrepeatable, inaccurate and unreliable because of the entrained air.”

Hedrick adds that Endress+Hauser worked with its bakery customer to make this very difficult application work. “We looked at the overall process, and made recommendations on how they could improve the process to reduce the amount of air,” he explains. “We installed a perforated plate to put backpressure on the meter, thereby reducing air pockets. In addition, we provided a Promass 83I full-bore, single-tube, Coriolis mass flowmeter to minimize pressure loss. Digital signal processing capabilities in the electronics of the meter enabled successful results despite the challenging conditions.”

These and other challenging flow measurement problems can be solved by calling in an independent consultant or a flowmeter supplier. Consultants aren’t beholden to any supplier, and can thus recommend the best solution from a wide range of choices, but they may not have detailed knowledge of each flowmeter type. Meanwhile, suppliers with a wide range of flowmeter types can be another good source for solutions. They have the ability to produce custom products, and can also offer innovative ways to apply their off-the-shelf offerings. 

[sidebar id =3]

Sponsored Recommendations

Measurement instrumentation for improving hydrogen storage and transport

Hydrogen provides a decarbonization opportunity. Learn more about maximizing the potential of hydrogen.

Get Hands-On Training in Emerson's Interactive Plant Environment

Enhance the training experience and increase retention by training hands-on in Emerson's Interactive Plant Environment. Build skills here so you have them where and when it matters...

Learn About: Micro Motion™ 4700 Config I/O Coriolis Transmitter

An Advanced Transmitter that Expands Connectivity

Learn about: Micro Motion G-Series Coriolis Flow and Density Meters

The Micro Motion G-Series is designed to help you access the benefits of Coriolis technology even when available space is limited.