Where wireless meets intrinsic safety

Oct. 21, 2016
How to deal with the constraints of putting access points in hazardous areas.

In an ideal world, it wouldn’t be necessary to worry about explosive atmospheres. Unfortunately, plant environments are far from ideal, with most process plants being about 80% Class I, Div. 2 (Zone 2) and another 10% Class I Div. 1 (Zone 1), so some protection is the norm. This is one constraint faced by network designers.

If we could install all the required wireless network access points in unclassified areas, things would continue to be easy. Unfortunately, this isn’t the case, and we need to place access points anywhere they’re required—unless, of course, we wish to spend significant effort with corresponding impact to system complexity by forcing the design to fit the area classifications. This is constraint two.

Consistent with our bias toward running one cable to every device with Power over Ethernet (PoE), defined in the 802.3af/at specifications, we’d prefer to go that route if feasible. The most common PoE today is based on IEEE 802.3af and 802.3at, which is backwards compatible with 802.3af. IEEE 802.2af provides power up to 15 watts per port, and 802.3at provides up to 25 watts per port to support higher-powered devices. The standards divide PoE devices into five classes based on the maximum average power available at powered device: Class 0 is 13.0 W, Class 1 is 3.84 W, Class 2 is 6.49 W, Class 3 is 13.0 W and Class 4 is 25.5 W.


Another reason for using PoE is to assure reliable power to the access point: PoE can be sourced from the interface room on the same UPS as the control system, rather than field-powered at a local panel. Power sourced from field panels is more susceptible to interruption and quality issues such as surges. Partially in response to this and similar demands, UPS units are now available for Class I, Div. 2 (Zone 2). These units add complexity to design and maintenance, and because they’re field-mounted, are likely to have lower reliability than equipment in a clean interface room environment. Constraint three.

[pullquote]Normally, at three strikes you’re out. In this case, we still have options. Because explosion-proof enclosures are metal, the “box” also works well as a Faraday cage, keeping radio signals out. Manufacturers have developed antenna arrangements that transition from the safe environment inside the enclosure to the outside to capture signals, so explosion-proof remains one choice we can use.

This configuration of safe area inside the enclosure with the other side exposed to the explosive atmosphere is similar to galvanic isolation, where one side of the isolation barrier is intrinsically safe, while the other side is unclassified. Galvanic isolators are often used in pairs, with equipment between the isolators considered equivalent to intrinsically safe (IS).

Some manufacturers make galvanic isolators designed for PoE installations that manage power on the CAT 5/6 cable, so if something happens on the cable to cause an arc or spark, the result won’t cause an explosion.

Ideally, the full system would be suitable for deployment and maintenance in any classified area, which means an IS system. The definition of  IS is: amount of energy that can be released in the hazardous area in the event of fault is voltage/power-limited to less than 30 V and less than 4 Watts.

At least one manufacturer has developed a fully IS Ethernet solution with a range of products, and also offers an IS interface to third parties for incorporation into their equipment with a maximum 12-VDC output. The company’s offerings are 200 mA at 10.9 VDC-Ex ia IIB (Class I, Div. 1, Groups C, D) output and 400 mA at 11.8 VDC-Ex ib IIB (Group B) output, and include IS PoE network devices.

Unfortunately, the above IS solutions are manufacturer-specific, which means you must purchase all the elements of the solution from the same supplier. This may not be a problem since most organizations tend to limit the number of suppliers used in their facilities.

[sidebar id =1]

Sponsored Recommendations

Measurement instrumentation for improving hydrogen storage and transport

Hydrogen provides a decarbonization opportunity. Learn more about maximizing the potential of hydrogen.

Get Hands-On Training in Emerson's Interactive Plant Environment

Enhance the training experience and increase retention by training hands-on in Emerson's Interactive Plant Environment. Build skills here so you have them where and when it matters...

Learn About: Micro Motion™ 4700 Config I/O Coriolis Transmitter

An Advanced Transmitter that Expands Connectivity

Learn about: Micro Motion G-Series Coriolis Flow and Density Meters

The Micro Motion G-Series is designed to help you access the benefits of Coriolis technology even when available space is limited.